EasyTouch Wireless 2 Handheld User Manual details for FCC ID P4HEASYTOUCH2A made by Pentair Aquatic Systems. Document Includes User Manual 520688 Rev E 10-04-11.
- Pentair Easytouch Troubleshooting
- Pentair Easytouch Control System Manual
- Pentair Easy Touch Control
- Pentair Control Panel Manual
- Pentair Pool Control System Manual
- Jul 03, 2019 Pentair 520591 EasyTouch 4P Single Body, Pool or Spa, Control System, Base System - No ICP, No Actuators. User Manual pdf Warranty pdf Warranty & Support Manufacturer’s warranty can be requested from customer service. Click here to make a request to.
- Apr 12, 2015 The EasyTouch wireless control panel gives you the freedom to control your pool or spa daily operations from around your pool and spa area. The wireless device can operate up to 300 feet from the EasyTouch transceiver module which is typically located near the EasyTouch load center.
11
EasyTouch Load Center Installation Guide
Installing Conduit and Wire to the EasyTouch Load Center
Before installing electrical conduit, read the following recommended guidelines:
•
Pentair Easytouch Troubleshooting
Determine the number of low and high voltage circuits being used in the EasyTouch load
center, the conduit size and runs needed based on the wire size, and the number of
conductors within the conduit.
•
Use 14 minimum to 6 maximum AWG for relay circuits depending on the load requirement.
Be sure to follow all regulation safety codes for the number and size of conductors that can
be installed in various sizes of conduit.
•
Power supply cable to the EasyTouch load center must have a minimum supply conductor
current of 60 AMP.
•
Supply circuit must be protected by suitable breaker rated no higher than 125 AMP.
•
To avoid obstruction into the EasyTouch load center, when using electrical conduit complete
the installation of the conduit before concrete is poured. Also, underground conduit should
be positioned in well compacted soil. Ensure that all conduit joints are well sealed and
watertight.
To install electrical conduit and wires as needed:
WARNING - TO AVOID AN ELECTRICAL HAZARD - Do not connect the power
source conductors to the EasyTouch load center circuit breaker until all electrical
connections for all loads (heaters, pumps, motorized valves, and lights etc.) have
been completed.
• Use the one of the three low voltage raceway 3/4' holes located on the underside of the
enclosure for the temperature sensor wires (see page 17).
• For the AC power wire into the EasyTouch load center from the main circuit breaker at the
house, use three conductors, one each for red, black, and white (or red, red and black for
220 VAC). The maximum load is 125 AMP at 120 VAC/240 VAC 60 Hz/50 Hz. These
conductors should be secured to supply side of circuit breaker base. Use a 1' conduit run for
these power conductors. For the main AC power conduit, it is recommended to use the 1'
conduit knockout located directly under the enclosure circuit breaker.
CAUTION All of the electrical wiring methods and materials used to complete the electrical
installation of the EasyTouch Pool/Spa Control System must be in accordance with the National
Electrical Code or the Canadian Electric Code, as well as any local electrical codes in effect at the
time of installation.
CAUTION All electrical materials used for the EasyTouch installation must be accomplished by,
or be under the direct supervision of a qualified electrician.
i
EasyTouch Load Center Installation Guide
Contents
IMPORTANT SAFETY INSTRUCTIONS ........................................................................ ii
General Installation Information ...................................................................................... iii
Technical Support ........................................................................................................... iv
EasyTouch 8 and 4 Pool and Spa Control System Kit Contents ..................................... 1
EasyTouch Accessory Equipment ................................................................................... 1
EasyTouch System Installation Steps Summary ............................................................. 2
Required Tools ................................................................................................................ 2
Plumbing Requirements ................................................................................................. 3
Equipment Location ........................................................................................................ 4
EasyTouch Load Center High Voltage Connections ....................................................... 6
EasyTouch Load Center Location ................................................................................... 6
Preparing the EasyTouch Load Center ........................................................................... 8
Mounting the EasyTouch Load Center ............................................................................ 9
Removing Electrical Conduit Knockouts ....................................................................... 10
Installing Conduit and Wire to the EasyTouch Load Center .......................................... 11
EasyTouch Motherboard Connections .......................................................................... 13
Accessing the EasyTouch Motherboard ........................................................................ 14
Installing Auxiliary Relays ............................................................................................. 15
Installing Valve Actuators .............................................................................................. 16
Installing and Connecting Temperature Sensors ........................................................... 17
Water Temperature Sensor ........................................................................................ 17
Ambient Air Temperature (Freeze Protection) Sensor ................................................ 17
Solar Temperature Sensor (Optional) ........................................................................ 17
Connecting the Heater Thermostat ............................................................................ 18
Pentair Easytouch Control System Manual
Connecting the IntelliChlor Cell .................................................................................... 19
Rewiring the IntelliChlor Transformer for 115 VAC ........................................................ 20
EasyTouch System Start-Up ......................................................................................... 21
Verifying IntelliChlor Power ........................................................................................... 22
EasyTouch System Wiring Diagram .............................................................................. 23
Pentair Easy Touch Control
Glossary ........................................................................................................................ 24